Controller Tower

Product Name : SpeedyBee BLS 55A 30x30 4-in-1 ESC Firmware : BLHeli_S J-H-40 PC Configurator Download Link : https://esc-configurator.com/ Continuous Current : 55A * 4 Burst Current : 70(10 seconds) TVS Protective diode : Yes External Capacitor : 1000uF Low ESR Capacitor(In the package) ESC Protocol : DSHOT300/600 Power Input : 3-6S LiPo Power Output : VBAT Current Sensor : Support (Scale=400 Offset=0) ESC Telemetry : Not supported Mounting : 30.5 x 30.5mm( 4mm hole diameter) Dimension : 45.6(L) * 44(W) *8mm(H) Weight : 23.5g Product Name : SpeedyBee F405 V4 30x30 Flight Controller MCU : STM32F405 IMU(Gyro) : ICM42688P USB Port Type : Type-C Barometer : Built-in OSD Chip : AT7456E chip BLE Bluetooth : Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4) WIFI : Not supported DJI Air Unit Connection Way : Two ways supported: 6-pin connector or direct soldering. 6-pin DJI Air Unit Plug : Supported. Complet..

Features Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required) FC indicator LEDs for visual debugging With LC filter FC Specifications MCU: STM32 F722 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFRC-IFLIGHT_BLITZ_F722 Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter Dimensions: 36.5*35 mm Weight: 7.8g BEC:  5V 2.5A / 9V 2A Wiring Suggestion UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemetry ESC Specifications Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 15.3g Supports 2-6S lipo input MCU: G071 Constant: 55 Amps  Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports..

BLITZ F7 Pro Combo Set ( F7 pro FC + E80 ) RC-006 Features Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required) FC indicator LEDs for visual debugging 512MB BlackBox With LC filter The MOSFET used by BLITZ E80 is PSMN1R0-40YLD, which can withstand a continuous current of 80A at 25°C, with a maximum power dissipation of 198W. BEC power supply adopts TI automotive-grade dedicated synchronous rectifier chip, supporting up to 100V. The 1-4 layer power board of the PCB circuit is ultra-thick copper with a thickness of 4OZ, ensuring continuous output under high-power operation. The STM32F051 main control processor with a running frequency of up to 48MHz, combined with a three-in-one driver IC, achieves a faster running speed! FC Specifications Product Name: BLITZ F7 Pro Flight Controller Mount pattern: 35*35mm/ 4mm PCB hole diameter Smartaudio / IRC Tramp VTX protocol supported Firmware target: ..